Binkp/1.0 The protocol description Binkp works via a bidirectional character channel committing no errors during data transfer. Any data each of the partners write into the channel has the following common format: binkp's frames: +---------------------- 0=data block, 1=message(command) | +---- data block size / msg's argument size | | 7 6543210 76543210 +-+-------+--------+--- ..... ---+ | | HI LO | | -- data block / msg's argument +-+-------+--------+--- ..... ---+ |<- 2 bytes ->|<- 32K max ->| The frame header contains two bytes defining the type and the length (in bytes) of the data that follows the header. If the most significant bit of the header is reset, then all the data received with the frame should be appended to the current file being received if the file has been opened, otherwise the data should be discarded. If the bit is set, the data should be considered as a command changing the protocol state. The first data byte in the frame is the command number. The rest of the bytes form an argument. A command argument is an arbitrary character set not required to be bounded with a '\0'. A command without arguments (for example M_OK) may look roughly this way: 7 6543210 76543210 76543210 +-+-------+--------+--------+ |1| 0 1| 4| +-+-------+--------+--------+ | | +----- the command number (no arguments) | +-------- length of the frame without the header - 1 byte +- this is a command The commands which binkd/0.8 understands and their arguments: M_NUL 0 The command argument is ignored (and is possibly logged). This is the way we transmit the nodelist information, the sysop’s name and so on. eg, "ZYZ Dima Maloff" M_ADR 1 A list of 5D addresses delimited by spaces. eg, "2:5047/13@fidonet 2:5047/0@fidonet" M_PWD 2 A password. After the successful processing of the password received from the remote, the binkd server rescans the queue. eg, "pAsSwOrD" M_OK 4 A reply to the correct password. The binkd client rescans the queue after receiving the message. The command argument is ignored. eg, "" M_FILE 3 The properties of the next file. They are delimited by spaces: filename without spaces, size, UNIX-time, the offset to transfer the file. All the numbers are decimal. All the data blocks received after that relate to this file until the next M_FILE is received. There is no special end-of-file marker since the file size is known beforehand. Binkd will append the "excessive" blocks to the current file. We start transmitting every new file from the offset 0. On receiving M_GET from the remote system we must do the seek operation. eg, "config.sys 125 2476327846 0" Or, answering to M_GET with offset 100: "config.sys 125 2476327846 100" M_EOB 5 End-of-Batch. EOB is transmitted after all the files have been sent. If we are in the EOB state (all the files are sent), we get EOB from the remote (no more files for us), we received all acknowledgements for all the sent files, we received all the files resent in reply to GET, then the session is considered to be successfully completed. eg, "" M_GOT 6 It is sent as an acknowledgement by the system which has received a file after receiving the last portion of the file data. The arguments are copies of the FILE command arguments received from the remote system except the last one, the offset which should not be returned to the system which sent M_FILE. GOT may also be sent during the process of receiving a file; the sending partner should react to it with the destructive skip. eg, "config.sys 125 2476327846" M_ERR 7 A fatal error. The partner who has sent M_ERR aborts the session. The argument contains the text explaining the reason and it is logged. Binkd sends M_ERR in response to an incorrect password. eg, "Incorrect password" M_BSY 8 Our system sends it if it is busy. The receiving partner ignores the argument (logs it). eg, "Too many servers are running already" M_GET 9 M_GET is used as a request to resend a file. The M_GET arguments copy the arguments of the M_FILE command which we’d like to see from the remote system. :) Binkd sends it as a response to M_FILE if it does not like the offset from which the file transmission has been started by the remote system. eg, "config.sys 125 2476327846 100" At present binkd handles it as follows: according to the first fields (name/size/UNIX-time) it determines whether the M_GET argument is the file we currently transmit (or the file has been transmitted and we are waiting for M_GOT for it). If this is the case it seeks the specified offset in the file and sends M_FILE after that. For the example above M_FILE will have the following arguments: "config.sys 125 2476327846 100" M_SKIP 10 Non destructive skip. An example of the argument line: "config.sys 125 2476327846" A typical session between two binkd mailers: The calling partner sends The answering partner sends M_NUL "SYS ..." M_NUL "SYS ..." M_NUL "ZYZ ..." M_NUL "ZYZ ..." M_NUL "LOC ..." M_NUL "LOC ..." M_NUL "VER ..." M_NUL "VER ..." M_ADR "2:2/2.2@fidonet" M_ADR "3:3/3.3@fidonet" M_PWD "password" (Waiting for a password from the remote system.) M_OK "" or M_ERR "Bad password" (Waiting for M_OK) M_FILE "file2 200 42342434 0" M_FILE "file1 100 423424244 0" data data data data data M_EOB (получили file1 целиком, подтверждаем) (file2 is received, acknowledging it) M_GOT "file1 100 423424244" M_GOT "file2 200 42342434" data M_EOB (c) Copyright 1996-97 by Dima Maloff Id: binkp.html,v 1.5 1998/10/08 07:31:48 maloff Exp Translated from Russian by Michael Dukelsky